Networks
By Stuart
LAN/WAN
Topologies
Ring topology
Some advantages include: 1) This type of network topology is very organized. Each node gets to send the data when it receives an empty token. This helps to reduces chances of collision. Also in ring topology all the traffic flows in only one direction at very high speed.
2) Even when the load on the network increases, its performance is better than that of Bus topology.
3) There is no need for network server to control the connectivity between workstations.
4) Additional components do not affect the performance of network.
5) Each computer has equal access to resources.
Some disadvantages include: 1) Each packet of data must pass through all the computers between source and destination. This makes it slower than Star topology.
2) If one workstation or port goes down, the entire network gets affected.
3) Network is highly dependent on the wire which connects different components.
4) MAU’s and network cards are expensive as compared to Ethernet cards and hubs.
Bus topology
Bus Topology is the simplest of network topologies. In this type of topology, all the nodes (computers as well as servers) are connected to the single cable (called bus), by the help of interface connectors. This central cable is the backbone of the network and is known as Bus (thus the name). Every workstation communicates with the other device through this Bus. A signal from the source is broadcasted and it travels to all workstations connected to bus cable. Although the message is broadcasted but only the intended recipient, whose MAC address or IP address matches, accepts it. If the MAC /IP address of machine doesn’t match with the intended address, machine discards the signal. A terminator is added at ends of the central cable, to prevent bouncing of signals. A barrel connector can be used to extend it
Some advantages include:
1) It is easy to set-up and extend bus network.
2) Cable length required for this topology is the least compared to other networks.
3) Bus topology costs very less.
4) Linear Bus network is mostly used in small networks. Good for LAN.
Some disadvantages include:
1) There is a limit on central cable length and number of nodes that can be connected.
2) Dependency on central cable in this topology has its disadvantages.If the main cable (i.e. bus ) encounters some problem, whole network breaks down.
3) Proper termination is required to dump signals. Use of terminators is must.
4) It is difficult to detect and troubleshoot fault at individual station.
5) Maintenance costs can get higher with time.
6) Efficiency of Bus network reduces, as the number of devices connected to it increases.
7) It is not suitable for networks with heavy traffic.
8) Security is very low because all the computers receive the sent signal from the source.
Star topology
In Star topology, all the components of network are connected to the central device called “hub” which may be a hub, a router or a switch. Unlike Bus topology (discussed earlier), where nodes were connected to central cable, here all the workstations are connected to central device with a point-to-point connection. So it can be said that every computer is indirectly connected to every other node by the help of “hub”. All the data on the star topology passes through the central device before reaching the intended destination. Hub acts as a junction to connect different nodes present in Star Network, and at the same time it manages and controls whole of the network. Depending on which central device is used, “hub” can act as repeater or signal booster. Central device can also communicate with other hubs of different network. Unshielded Twisted Pair (UTP) Ethernet cable is used to connect workstations to central node.
Some advantages include:
1) As compared to Bus topology it gives far much better performance, signals don’t necessarily get transmitted to all the workstations. A sent signal reaches the intended destination after passing through no more than 3-4 devices and 2-3 links. Performance of the network is dependent on the capacity of central hub.
2) Easy to connect new nodes or devices. In star topology new nodes can be added easily without affecting rest of the network. Similarly components can also be removed easily.
3) Centralized management. It helps in monitoring the network.
4) Failure of one node or link doesn’t affect the rest of network. At the same time its easy to detect the failure and troubleshoot it.
Some disadvantages include:
1) Too much dependency on central device has its own drawbacks. If it fails whole network goes down.
2) The use of hub, a router or a switch as central device increases the overall cost of the network.
3) Performance and as well number of nodes which can be added in such topology is depended on capacity of central device.